NXP i.MX 8QuadMax Multisensory Enablement Kit (MEK)

Preparation

Important

Ensure you replace the <factory> placeholder below with the name of your Factory.

Download necessary files from https://app.foundries.io/factories/<factory>/targets
1. Click the latest Target with the platform trigger.
2. Expand the run in the Runs section which corresponds with the name of the board. Download the Factory image for that machine. For example:
  lmp-factory-image-<machine-name>.wic.gz u-boot-<machine-name>.itb imx-boot-<machine-name>
Extract the file lmp-factory-image-<machine-name>.wic.gz:
```
gunzip lmp-factory-image-<machine-name>.wic.gz
```
Expand the run in the Runs section which corresponds with the name of the board. Download the mfgtools for that machine, e.g., mfgtool-files-<machine-name>.tar.gz.

Extract the file

tar -zxvf mfgtool-files-<machine-name>.tar.gz

Organize all the files, mirroring the tree below:

├── lmp-factory-image-<machine-name>.wic.gz
├── u-boot-<machine-name>.itb
├── imx-boot-<machine-name>
└── mfgtool-files-<machine-name>
    ├── bootloader.uuu
    ├── full_image.uuu
    ├── SPL-mfgtool
    ├── u-boot-mfgtool.itb
    ├── uuu
    └── uuu.exe

Hardware Preparation

Set up the board for updating using the manufacturing tools:

Connect the micro-B end of the supplied USB cable into Debug UART port J18. Connect the other end of the cable to a host computer.
Connect Type-C into USB Type-C port J17. Connect the other end of the cable to a host computer.
Use boot switch (SW2) to configure to boot from SDP ([D1-D6]: 000100).

Fig. 75 Boot switches
Power the board by flipping the switch (SW1).

Flashing

Once in serial downloader mode and connected to your PC, the evaluation board should show up as a Freescale USB device.

Note

Device names and IDs can slightly differ from the steps below.

Verify target is present:
```
$ lsusb | grep Freescale
Bus 002 Device 052: ID 15a2:0080 Freescale Semiconductor, Inc.
```
In this mode, you will use the uuu tools to program the images to the eMMC.

Run the command below to program the LmP to the EMMC:

$ sudo mfgtool-files-<machine-name>/uuu -pp 1 mfgtool-files-<machine-name>/full_image.uuu
uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.43-0-ga9c099a

Success 1    Failure 0


1:31     3/ 3 [=================100%=================] SDPV: jump
2:31     8/ 8 [Done                                  ] FB: done

Turn off the power.
Put the board into run mode

Start the Device Manager
Select View
Select Devices by container
Verify a device like the following:

Run the command below to program the LmP to the EMMC:

C:\Users\Someone> mfgtool-files-<machine-name>\uuu.exe -pp 1 mfgtool-files-<machine-name>\full_image.uuu
uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.43-0-ga9c099a

Success 1    Failure 0


1:31     3/ 3 [=================100%=================] SDPV: jump
2:31     8/ 8 [Done                                  ] FB: done

Turn off the power.
Put the board into run mode

Configure the boot switch (SW2) to boot from eMMC ([D1-D6]: 001000). Power on the board to boot the new image.