Intel Core i7 CPU (and later) - Installing into Internal Flash

To install the system image into an internal flash drive, you should enable the WIC Image Installer.

With the WIC installer enabled, follow the instructions to flash the installer into a USB stick/SD Card.

Preparation

Ensure you replace the <factory> placeholder below with the name of your Factory.

  1. Download necessary files from https://app.foundries.io/factories/<factory>/targets

    1. Click the latest Target with the platform-devel Trigger.

      ../../_images/generic-steps-1.png

    2. Expand the run in the Runs section which corresponds with the name of the board and download the Factory image for that machine.

      E.g: lmp-factory-image-<machine-name>.wic.gz

      ../../_images/generic-steps-2.png

Flashing

Now, flash the lmp-factory-image-intel-corei7-64.wic.gz retrieved from the previous section to a USB Stick/SD Card. This contains the system image installer.

Linux
macOS
Windows

  1. Determine the disk you want to flash by finding the device with the SIZE that matches your flash drive in the list below. Be sure to ignore partitions (where TYPE is part). Save the NAME for your flash drive to be used in a later step as the disk path. e.g: /dev/mmcblk0, /dev/sdb:

    lsblk -po +MODEL

    Example Output:

    $ lsblk -po +MODEL
NAME             MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT                 MODEL
/dev/mmcblk0     179:0    0  29.8G  0 disk
├─/dev/mmcblk0p1 179:1    0  41.6M  0 part /mnt/boot
└─/dev/mmcblk0p2 179:2    0  29.8G  0 part /mnt/otaroot
/dev/zram0       254:0    0    26G  0 disk /out
/dev/nvme0n1     259:0    0 953.9G  0 disk                            SSDPEKKF010T8 NVMe INTEL 1024GB

  2. Flash the disk.

    Replace <system-image> with the path to your system image.
    Replace /dev/mmcblk<X> with your chosen disk path.
gunzip -c <system-image> | sudo dd of=/dev/mmcblk<X> bs=4M iflag=fullblock oflag=direct status=progress

  1. Determine the disk you want to flash by finding the device with the SIZE that matches your flash drive in the list below. Be sure to ignore partitions (lines without the * in the SIZE). Save the IDENTIFIER for your flash drive to be used in a later step as the disk path. e.g: /dev/disk3:

    diskutil list

    Example Output:

    $ diskutil list
/dev/disk3 (internal, physical):
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:     FDisk_partition_scheme                        *15.5 GB    disk3
   1:             Windows_FAT_32 boot                    45.7 MB    disk3s1
   2:                      Linux                         15.5 GB    disk3s2

  2. Flash the disk.

    Replace <system-image> with the path to your system image.
    Replace /dev/disk<X> with your chosen disk path.
gunzip -c <system-image> | sudo dd of=/dev/disk<X> bs=4M

Windows has no dd like tool built into the operating system to flash your image to disk. In this case, we recommend you download and use either Win32 Disk Imager or Rufus.

Note

Your system image is in a compressed wic.gz format. To follow these next steps, you must extract it using a tool like 7zip which will leave you with a .wic image file.

Using Rufus

  1. Download and run Rufus.
  2. Select your disk.
  3. SELECT your <system-image>.
  4. START the flash procedure.

Using Win32 Disk Imager

  1. Download and run Win32 Disk Imager as Administrator.
  2. Click the blue folder icon.
  3. Select your <system-image>
  4. Select your disk via the Device dropdown.
  5. Click Write
  6. Wait for the image to finish writing, and a Write Successful dialog will appear.
  1. Remove the flash drive from the host and insert/connect it into the board.
  2. Power on the board to boot the new image.

Most Intel devices will boot from USB automatically. If the device doesn’t automatically boot from USB, try holding F12 when your device first boots. This will allow you to select the device from a system-specific boot menu.

If F12 doesn’t work for you, check your device documentation to find how to bring up the boot menu.

Booting installer

Warning

The following steps will delete all your programs, documents, photos, music, and any other files on the selected device.

After boot, wait until the message:

Please select an install target or press n to exit (sda sdc)
sda

Type the name of the device you want to install the system image. In the example above, the device used was sda.

Right after select the device, the prompt will ask if you want to proceed:

Proceed anyway? (y,N)

Type y if you want to continue the installation.

When the installation completes, the following message will be displayed:

Installation successful. Remove your installation media and press Enter to reboot.

Follow the instructions and reboot the device.