i.MX 8M Plus Evaluation Kit

Preparation

The instructions in this section also applies to those boards with secure boot enabled. There are references on how to perform common instructions along with the flow. Security details the required background for secure boot.

Important

Ensure you replace <factory> placeholder below with the name of your Factory.

Download the necessary files from https://app.foundries.io/factories/<factory>/targets:
1. Click the latest Target with the platform trigger.
2. Expand the run in the Runs section which corresponds with the name of the board. Download the Factory image for that machine. For example:
  lmp-factory-image-<machine_name>.wic.gz u-boot-<machine_name>.itb imx-boot-<machine_name>
Note

The compressed image (.wic.gz) is used since LmP v92. Before, the scripts required a compressed file image (.wic).
Download and extract the file mfgtool-files-<machine_name>.tar.gz:
```
tar -zxvf mfgtool-files-imx8mp-lpddr4-evk.tar.gz
```

Organize all the files, mirroring the tree below:

├── lmp-factory-image-imx8mp-lpddr4-evk.wic.gz
├── u-boot-imx8mp-lpddr4-evk.itb
├── sit-imx8mp-lpddr4-evk.bin
├── imx-boot-imx8mp-lpddr4-evk
└── mfgtool-files-imx8mp-lpddr4-evk
     ├── bootloader.uuu
     ├── full_image.uuu
     ├── imx-boot-mfgtool
     ├── uuu
     └── uuu.exe

Hardware Preparation

Set up the board for updating using the manufacturing tools:

Top view of i.MX 8M Plus EVK

OPTIONAL. Only required if you have problems or want to see the boot console output.
Connect the micro-B end of the USB cable into debug port J23. Connect the other end of the cable to a PC acting as a host terminal. Four UART connections will appear on the PC. For example, on a Linux host:
ls -l /dev/serial/by-id/ otal 0 rwxrwxrwx 1 root root 13 jan 24 10:24 usb-FTDI_Quad_RS232-HS-if00-port0 -> ../../ttyUSB0 rwxrwxrwx 1 root root 13 jan 24 10:24 usb-FTDI_Quad_RS232-HS-if01-port0 -> ../../ttyUSB1 rwxrwxrwx 1 root root 13 jan 24 10:24 usb-FTDI_Quad_RS232-HS-if02-port0 -> ../../ttyUSB2 rwxrwxrwx 1 root root 13 jan 24 10:24 usb-FTDI_Quad_RS232-HS-if03-port0 -> ../../ttyUSB3
Using a serial terminal program like minicom, connect to the port with if02 in the name (in this example ttyUSB2). Apply the following configuration:
Baud rate: 115200

Data bits: 8

Stop bit: 1

Parity: None

Flow control: None
Ensure that the power is off (SW3)
Put the i.MX 8M Plus EVK into programing mode:

Switch SW4 to OFF, OFF, OFF, ON (from 1-4 bit) to Download Mode.

Location of SW4 dip switch on i.MX 8M Plus EVK
Connect your computer to the i.MX 8M Plus EVK board via the USB-C port 1 Download J6 jack.
Connect the USB-C power plug to the port 2 Power J5 jack.
Power on the i.MX 8M Plus EVK board by sliding power switch SW3 to ON.

Flashing

Once in serial downloader mode and connected to your PC, the evaluation board should show up as an NXP® USB device.

For instructions on how to sign the required images before flashing them to the board with secure boot enabled, see Machines with Secure Aspects Enabled by FoundriesFactory

Verify target is present:

lsusb | grep NXP
 Bus 001 Device 023: ID 1fc9:012b NXP Semiconductors i.MX 8M Dual/8M QuadLite/8M Quad Serial Downloader

In this mode you will use the uuu tools to program the images to the eMMC. The USB ID may differ if a different SoC is used.

To program the LmP to the EMMC run

$ sudo mfgtool-files-imx8mp-lpddr4-evk/uuu mfgtool-files-imx8mp-lpddr4-evk/full_image.uuu
  uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.243-0-ged48c51

  Success 1    Failure 0


  1:92     6/ 6 [Done                                  ] FB: done

Turn off the power
Put the board into run mode

Start the Device Manager
Select View
Select Devices by container
Verify a device like the following:

Run the command below to program the LmP to the EMMC:

C:\Users\Someone> mfgtool-files-imx8mp-lpddr4-evk\uuu.exe mfgtool-files-imx8mp-lpddr4-evk\full_image.uuu
  uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.243-0-ged48c51

  Success 1    Failure 0


  1:92     6/ 6 [Done                                  ] FB: done

Turn off the power.
Put the board into run mode

Put the i.MX 8M Plus EVK into run mode by switching SW4 to OFF, ON, OFF, OFF to set the board to boot from eMMC.

Power on the i.MX 8M Plus EVK board by sliding the power switch SW3 to ON.